Bucket Buddy – the bucket washer that combines hot water, detergent and brushes

Clean buckets for healthy calves and lambs. Every bucket, every feeding, the same result.

  • Thorough: hot water, automatically dosed detergent and mechanical brushing, inside and out
  • Always the same result, whoever feeds and however busy it gets
Bucket Buddy bucket washer in stainless steel with control box, motor and a calf bucket on the brushes

A bucket that looks clean is not clean yet

After every feeding, a thin layer of milk fat remains in the bucket. Bacteria grow quickly in it, even when the bucket looks clean. That way, the next calf or lamb gets a dose of pathogens with every feeding.

Diarrhoea is the leading cause of death in young calves, and young animals get infected through the mouth. A dirty bucket is therefore one of the most important sources of infection on the farm.

Every farmer knows buckets need to be cleaned properly. But with dozens to hundreds of buckets a day, at busy times, with a different worker or at the end of a long day, it quickly becomes just a rinse. And rinsing alone is not enough.

Stack of dirty calf buckets in the barn, next to a dairy farmer washing buckets by hand

Rinsing alone is not enough

The layer of fat in which bacteria hide can only be removed with hot water, a detergent and mechanical brushing. That is what vets advise. The Bucket Buddy does all three, for every bucket.

Hot water

Straight from the boiler on your farm, at 60 °C. Hot water dissolves the milk fat that cold water only rinses around.

Detergent

Automatically drawn from a separate tank and mixed into the hot water. No measuring: every bucket gets the right dose.

Brushes

Three brushes mechanically scrub the bucket clean inside and out. That removes even the stubborn layer of fat.

Every bucket gets the same thorough cleaning, whoever feeds. That turns hygiene into a fixed routine instead of something that depends on the day.

A clean bucket in five steps

  1. 1

    Remove the teat

    Take the teat off the bucket, so the inside can be cleaned completely.

  2. 2

    Place the bucket

    With the lid open, the top brush points up, so the bucket fits in easily.

  3. 3

    Close the lid

    The top brush lowers into the bucket and clamps the wall firmly against the two bottom brushes.

  4. 4

    Start and clean

    Press the start button. The brushes spin, the bucket rotates along by itself and hot water with detergent cleans the inside and outside at the same time.

  5. 5

    Open the lid

    The top brush rises again and you take out a clean bucket.

Three brushes, one thorough cleaning

The Bucket Buddy works with three brushes: one on the inside of the bucket and two on the outside. As soon as the lid closes, the top brush lowers into the bucket and clamps the wall firmly against the two bottom brushes. When the lid opens, the top brush moves up again.

The brushes spin in different directions and at different speeds. That makes the bucket rotate along by itself, so the entire circumference passes the brushes, inside and out. Every centimetre gets brushed, including the spots you quickly miss by hand.

Clean water, inside and out

The hot water with detergent sprays through the brush that sits inside the bucket. That way it reaches the bucket directly, without detours and without contamination, and cleans the inside exactly where the milk fat sits. At the same time, water sprays over the outside from above, where hands, manure and barn dirt end up.

Simple to operate, precise to adjust

The Bucket Buddy works by default with a fixed cleaning programme: bucket in, lid closed, press the start button, done. When finished, the machine stops by itself and you can take out the clean bucket and place the next one. No settings are needed, so everyone on the farm can work with it right away.

Want to fine-tune the cleaning to your own farm? Then choose the optional touchscreen. With it you can easily set:

  • Cleaning time: how long the brushes and the water do their work
  • Dosing moment: when in the cycle the detergent is added
  • Amount of detergent: how much detergent is mixed in per bucket
  • Pre-rinse: optionally pre-rinse with cold water first to flush away milk residues, useful for heavily soiled buckets or after colostrum

Not just calf buckets

The Bucket Buddy cleans buckets from 200 to 400 mm wide and 200 to 500 mm high, in every shape: round, square, rectangular and teat buckets with a flat side. Think of drinking buckets, buckets for mixing milk, and water and concentrate buckets. Remove the teat before cleaning. Note: the buckets must withstand hot water of 60 °C. For most plastic calf buckets that is no problem.

Your detergent

The detergent sits in a separate tank and is mixed in automatically. We advise an alkaline detergent, because it dissolves fat and protein residues from milk well. You can also use a detergent you already have for the milking installation or the calf pens.

Who is it for?

Calf rearers

A fixed, thorough cleaning of every bucket for healthy calves. On top of that, you save time with dozens to hundreds of buckets a day.

Dairy farmers with own rearing

Clean buckets for a healthy start of your own young stock. At the same time you spend less time washing buckets around every feeding.

Goat and sheep farmers

Thoroughly cleaned drinking buckets for healthy lambs. That way cleaning after every feeding takes less time too.

Farms with an automatic feeder

The same thorough hygiene for buckets for colostrum and sick or separated calves. You clean those buckets with less manual work too.

What does a sick calf cost?

Diarrhoea is the leading cause of death in young calves. And even when a calf recovers, it costs money: treatment, growth delay and a greater chance of other diseases. A single diarrhoea outbreak in a rearing calf easily costs at least € 150 per calf.*

A clean bucket at every feeding is one of the simplest ways to reduce that risk.

And you save time

Cleaning a bucket properly by hand takes time. With the Bucket Buddy you place the bucket, press start and have your hands free for mixing milk or preparing the next bucket.

* Source: melkvee.nl

Specifications and connections

You simply connect the Bucket Buddy to your existing facilities. It has no pump or heating of its own, so there is less that can wear out or break.

Technical infographic of bucket shapes: round, flat side, square and rectangular, with width 200 to 400 mm and height 200 to 500 mm

Bucket and connection specifications

Bucket shape
Round, square, rectangular or teat bucket with a flat side
Diameter or width
200 – 400 mm
Height
200 – 500 mm
Teat
Remove beforehand
Water connection
Hot water tap (no own pump or heating)
Drain
Sewer
Power
230V, 50 Hz
Cleaning temperature
60 °C (via the hot water tap, depending on the boiler)
Detergent
Automatically mixed in from a separate tank
Detergent tank capacity
5 L
Brushes
3 pieces, different directions of rotation and speeds; bucket rotates along
Operation
Standard programme; optional touchscreen
Options
Touchscreen, pre-rinse
Water use per bucket
[litres]
Machine dimensions (l x w x h)
[mm]
Weight
[kg]

Hot water

Connection to the hot water tap.

Drain

Connection to the sewer.

Power

230V, 50 Hz.

Frequently asked questions

Cleaning takes 20 seconds, swapping about 10 seconds. Together 30 seconds per bucket, up to 120 buckets per hour.

Calf buckets, but also other buckets, such as water and concentrate buckets. The shape does not matter: round, square, rectangular buckets and teat buckets with one flat side all fit. The bucket must be 200 to 400 mm in diameter (or width) and 200 to 500 mm high. Remove the teat before cleaning.

A hot water tap and a drain to the sewer. The Bucket Buddy has no pump or heating of its own; it uses the hot water from your own installation.

We advise an alkaline detergent, because it dissolves fat and protein residues from milk well. The detergent is mixed in automatically from a separate tank. You can also use a detergent you already have for the milking installation or the calf pens.

Yes. Request a demo from Comfy-Solutions or your dealer, or visit us at a trade show.

The Bucket Buddy is connected to your farm's hot water tap and cleans with water of 60 °C. That is in line with vets' cleaning advice for young stock feeding equipment.

Yes. The two bottom brushes scrub the outside and water sprays over the bucket from above. That way the inside and outside are cleaned at the same time.

Yes. With the optional touchscreen you set the cleaning time, and when and how much detergent is added.

Most plastic calf buckets can withstand 60 °C. In doubt? Check with the manufacturer of your buckets.

Clean buckets, healthy calves. See it yourself.

See how hot water, detergent and brushes work together. Request a demo for your farm.

Calves eating grass at the feed fence in the barn